## Archive for the ‘Personal Injury’ Category

Wednesday, December 6th, 2017
Last time we developed an engineering formula to calculate the *horsepower* required to accelerate a *flywheel* by way of a *reciprocating steam engine, *which contributes to the storage of kinetic energy inside a flywheel. Today we’ll gain a clearer understanding of how this works when we take *a look inside a reciprocating steam engine.*
__A Look Inside a Reciprocating Steam Engine__
A *reciprocating steam engine* performs the work of transforming steam’s heat energy into the mechanical energy needed to move a piston contained within a cylinder. During a complete operating cycle this piston travels from one end of the cylinder to the other, then back again. This is made possible because during the first half of the cycle pressurized steam enters one end of the cylinder and expands inside it, forcing the piston to move.
This process inside the cylinder results in movement of a piston that’s attached to a piston rod, which in turn is connected to a crankshaft via a connecting rod and crank rod. The crankshaft is a device which converts the reciprocating linear motion of an engine’s piston into rotary motion and in so doing facilitates the powering of any externally mounted rotating machinery attached to it. So long as there’s ample steam to power the internal piston, over time, energy in the form of horsepower will be available to externally mounted devices. The energy in the steam decreases as the steam expands behind the moving piston. So, the engine’s horsepower, will decrease as the piston travels to the end of the cylinder. If the energy in the steam should become depleted, the *reciprocating steam engine *will stall. The engine will no longer be able to perform work.
Next time we’ll see how a crankshaft works when we take a look inside it.
opyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: connecting rod, crank rod, crankshaft, energy, engineering, flywheel, kinetic energy, piston rod, power, reciprocating steam engine, work

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | No Comments »

Friday, November 24th, 2017
Last time we discussed how torque is created as a *flywheel* spins. This *torque* is a factor of the *flywheel’s* moment of inertia, which is dependent on how far the masses of the flywheel’s parts are located from its center of rotation. Today we’ll present a formula to compute how much *horsepower is required to accelerate a flywheel*. And here it is,
__Horsepower Required to Accelerate a Flywheel__
where, *T* is the torque created on the flywheel’s shaft in units of inch-pounds. The term *n* is the flywheel shaft’s speed of rotation in revolutions per minute, *RPM*. *Horsepower, **HP,* is engineering shorthand for a unit of power equal to 6600 inch-pounds per second, and the number 63,025 is a constant needed to convert *torque,* *T,* and the spinning shaft’s rotations per minute, *RPM*, into *horsepower* units.
Torque is present whether the *flywheel’s* spin accelerates or decelerates. During acceleration torque is created, which contributes to the production of kinetic energy that’s stored inside the flywheel. When a flywheel’s spin decelerates, its *mass *experiences the effects of negative acceleration, and stored kinetic energy is released.
As we learned awhile back, horsepower is a function of torque in any moving machinery, including engines and flywheels. An engine must produce *horsepower to accelerate a flywheel* connected to its shaft. By the same token, when the engine’s horsepower output diminishes or stops, the flywheel begins to decelerate. This deceleration causes kinetic energy stored within the flywheel to be released, providing horsepower necessary to keep the engine and flywheel spinning. That is, until the power output of the engine returns or the stored kinetic energy of the flywheel is ultimately exhausted.
We’ll see how that works next time when we take a look inside a reciprocating engine.
opyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: acceleration, deceleration, engine, engineering, flywheel, horsepower, kinetic energy, mass, moment of inertia, torque

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Horsepower Required to Accelerate a Flywheel

Monday, November 13th, 2017
Last time we began our discussion on moment of inertia and how it affects a *flywheel’s* storage of kinetic energy. That inertia is a function of the *flywheel’s* *mass,* in particular how the *mass *is *distributed*. Today we’ll continue our discussion and see how an engineering principal known as *torque* affects things.
__Flywheel Torque and Distribution of Mass__
We learned in a previous blog that *torque* is most simply defined as a measure of how much force acts upon an object to cause it to rotate around a pivot point or center of rotation, shown as a small black dot in the illustration. For our discussion we’ll focus on two parts of the *flywheel,* the hub, part *A*, and the rim, part *E*.
Part *A* has a mass *m*_{A} located a distance *r*_{A} from the flywheel’s center, while part *E* has a mass *m*_{E} located a distance *r*_{E} from it. When an engine applies mechanical power to the flywheel by way of its rotating shaft, the revolutions per minute, RPM, increase and along with it the angular velocity, ω, also increases. For a refresher on this, follow the link.
Because of this relationship, we can calculate the kinetic energy contained within a flywheel using the kinetic energy formula,
*KE =* ½ × ∑[*m × **r*^{2}] × ω^{2} (1)
As the flywheel’s angular velocity increases or decreases in response to the engine’s energy output, parts *A* and *E* reflect acceleration or deceleration of *a*_{A} and *a*_{E}. Since parts *A* and *E* exhibit both mass and acceleration, they are subject to *Newton’s Second Law of Motion*, which states that force equals mass times acceleration. Using that relationship we can calculate the force exerted on each part by,
*F*_{A} = m_{A} ×* a*_{A} (2)
*F*_{E} = m_{E} ×* a*_{E} (3)
Part *A* is small compared to part *E*, therefore *m*_{E} is greater than *m*_{A} and accordingly *F*_{E} is greater than *F*_{A}. Forces *F*_{A} and *F*_{E} act as torques, because they cause parts *A* and *E* to rotate around the flywheel’s center of rotation, so they are designated as Torque *A*, *T*_{A, }and Torque *E*, *T*_{E. } These torques are computed by,
*T*_{A} = F_{A} ×* r*_{A} (4)
*T*_{E} = F_{E} ×* r*_{E} (5)
Part *E*’s greater mass will contribute more torque than part *A*, and it will also contribute more to the flywheel’s kinetic energy content.
Most flywheels are designed with heavy rims supported by small hubs and slender spokes, because the more mass that’s distributed away from the flywheel’s center of rotation, the greater the flywheel’s moment of inertia and torque, and the more kinetic energy it can store.
Next time we’ll develop an equation which allows us to quantify the horsepower required to accelerate a flywheel.
opyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: distribution of mass, engineering, flywheel, kinetic energy, mass, moment of inertia, torque

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Flywheel Torque and Distribution of Mass

Monday, November 6th, 2017
Last time we arrived at a general formula to compute the *kinetic energy*, KE, contained within the totality of a spinning* flywheel* made up of numerous parts. Today we’ll discuss the terms in that formula, which encompasses a phenomenon of *flywheels *known as *moment of inertia*.
__Moment of Inertia in a Flywheel__
The kinetic energy formula we’ve been working with is, again,
*KE =* ½ × Σ[*m × **r*^{2}] × *ω*^{2} (1)
The bracketed part of this equation makes reference to spinning *flywheels* comprised of one or more parts, and that’s what we’ll be focusing on today. The symbol Σ is the Greek letter sigma, standard engineering shorthand notation used to represent the sum of all terms and mathematical operations contained within the brackets.
Our illustration shows we have five parts to consider: a hub, three spokes and a rim, and label them *A*, *B*, *C*, *D*, and *E* respectively. Each part has its own mass, *m,* and is a unique distance, *r,* from the *flywheel’s *center of rotation. The *flywheel’s* angular velocity is represented by ω.
For our *flywheel* of parts *A* through *E *our expanded equation becomes,
Σ[*m × **r*^{2}] = [*m*_{A} × *r*_{A}^{2}] + [*m*_{B} × *r*_{B}^{2}] + [*m*_{C} × *r*_{C}^{2}] + [*m*_{D} × *r*_{D}^{2}] + [*m*_{E} × *r*_{E}^{2}] (2)
Equation (2) represents the sum total of *moments of inertia* contained within our *flywheel.* It’s a numerical representation of the flywheel’s degree of resistance to changes in motion.
The more mass a *flywheel* has, the greater its *moment of inertia.* When at rest this greater moment of inertia means it will take more effort to return it to motion. But once in motion the flywheel’s greater moment of inertia will make it harder to stop. That’s because there’s a lot of *kinetic energy *stored within its spinning mass, and the heavier a flywheel is, the more kinetic energy it contains. In fact, for any given angular velocity *ω*, a large and heavy flywheel stores more kinetic energy than a smaller, lighter flywheel.
But there’s more to a flywheel’s *moment of inertia* than just mass. What’s really important is how that mass is distributed. We’ll get into that next time when we discuss torque.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: angular velocity, center of rotation, engineering, flywheel, kinetic energy storage, mass, moment of inertia, spinning flywheel

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Moment of Inertia in a Flywheel

Thursday, October 26th, 2017
Last time we introduced the fact that spinning flywheels are subject to both linear and angular velocities, along with a formula that allows us to calculate these quantities for a single part of the flywheel, designated *A*. We also re-visited the *kinetic energy* formula. Today we’ll build upon those formulas as we attempt to answer the question, *How much kinetic energy is contained within a spinning flywheel?*
Here again is the basic *kinetic energy* formula,
*KE =* ½ × *m × **v*^{2} (1)
where, *m* equals a moving object’s mass and *v* is its linear velocity.
Here again is the formula used to calculate linear and angular velocities for a single part *A* within the flywheel, where part __A__’s linear velocity is designated *v*_{A}, angular velocity by *ω*, and where *r*_{A} is the distance of part *A* from the flywheel’s center of rotation.
*v*_{A} = r_{A} × ω (2)
Working with these two formulas, we’ll insert equation (2) into equation (1) to obtain a *kinetic energy *formula which allows us to calculate the amount of energy contained in part *A* of the flywheel,
*KE*_{A} = ½ *×* *m*_{A} *×* (*r*_{A} × *ω*)^{2} (3)
which simplifies to,
*KE*_{A} = ½ *×* *m*_{A} *×* *r*_{A}^{2} *× **ω*^{2} (4)
Equation (4) is a great place to begin to calculate the amount of *kinetic energy contained within a spinning flywheel,* however it is just a beginning, because a flywheel contains many parts. Each of those parts has its own mass, *m,* and is a unique distance, *r,* from the flywheel’s center of rotation, and all these parts must be accounted for in order to arrive at a calculation for the total amount of *kinetic energy contained within a spinning flywheel*.
__How Much Kinetic Energy is Contained Within a Spinning Flywheel?__
Put another way, we must add together all the *m × **r*^{2} terms for each and every part of the entire flywheel. How many parts are we speaking of? Well, that depends on the type of flywheel. We’ll discuss that in detail later, after we define a phenomenon that influences the *kinetic energy of a flywheel* known as the moment of inertia.
For now, let’s just consider the flywheel’s parts in general terms. A general formula to compute the *kinetic energy contained* within the totality of a *spinning flywheel* is,
*KE =* ½ *×* ∑[*m × **r*^{2}] *×* *ω*^{2} (5)
We’ll discuss the significance of each of these variables next time when we arrive at a method to calculate the *kinetic energy contained* within all the many parts of a *spinning flywheel*
.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: angular velocity, center of rotation, engineering, flywheel, kinetic energy, linear velocity, mass, moment of inertia

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability, Professional Malpractice | Comments Off on How Much Kinetic Energy is Contained Within a Spinning Flywheel?

Thursday, October 19th, 2017
Anyone who has spun a potter’s wheel is appreciative of the smooth motion of the flywheel upon which they form their clay, for without it the bowl they’re forming would display irregularities such as unattractive bumps. The flywheel’s smooth action comes as a result of *kinetic energy*, the energy of motion, stored within it. We’ll take another step towards examining this phenomenon today when we take our first look at calculating this kinetic energy. To do so we’ll make reference to the *two types of velocity associated with a spinning flywheel,* *angular velocity *and linear velocity, both of which engineers must negotiate anytime they deal with rotating objects.
Let’s begin by referring back to the formula for calculating *kinetic energy*, *KE*. This formula applies to all objects moving in a linear fashion, that is to say, traveling a straight path. Here it is again,
*KE =* ½ × *m × **v*^{2}
where *m* is the moving object’s mass and *v* its linear velocity.
Flywheels rotate about a fixed point rather than move in a straight line, but determining the amount of kinetic *energy* *stored within a spinning flywheel* involves an examination of both its *angular velocity* and linear velocity. In fact, the amount of *kinetic energy *stored within it depends on how fast it rotates.
For our example we’ll consider a spinning flywheel, which is basically a solid disc. For our illustrative purposes we’ll divide this disc into hypothetical parts, each having a mass *m* located a distance *r* from the flywheel’s center of rotation. We’ll select a single part to examine and call that *A*.
__Two Types of Velocity Associated With a Spinning Flywheel__
Part *A* has a mass, *m*_{A}, and is located a distance *r*_{A} from the flywheel’s center of rotation. As the flywheel spins, part *A* rides along with it at an angular velocity, ω, following a circular path, shown in green. It also moves at a linear velocity, *v*_{A}, shown in red. *v*_{A} represents the linear velocity of part *A* measured at any point tangent to its circular path. This linear velocity would become evident if part *A* were to become disengaged from the flywheel and cast into the air, whereupon its trajectory would follow a straight line tangent to its circular path.
The linear and angular velocities of part *A* are related by the formula,
*v*_{A} = r_{A} × ω
Next time we’ll use this equation to modify the basic kinetic energy formula so that it’s placed into terms that relate to a flywheel’s *angular velocity*. This will allow us to define a phenomenon at play in the flywheel’s rotation, known as the moment of inertia.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: angular velocity, energy stored, engineering, flywheel, kinetic energy, linear velocity, mass, moment of inertia, spinning flywheel

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability, Professional Malpractice | Comments Off on Two Types of Velocity Associated With a Spinning Flywheel

Tuesday, October 10th, 2017
Last time we introduced *angular velocity* with regard to **flywheel**s and how a fixed point riding piggyback on a moving flywheel travels the same circular path as its host at a pace that’s measured in units of degrees per second. Today we’ll introduce another unit of measure, the *radian*, and see how it’s uniquely used to measure angles of circular motion in units of radians per second.
__Radians and the Angular Velocity of a Flywheel__
Back in elementary school we worked with protractors and measured *angles* in degrees, and we were all too familiar with the fact that the average protractor maxed out at 180, or half the degrees present in a complete circle. But in the grownup worlds of physics and engineering, angles of circular motion are measured in units called *radians,* an international standard equal to 57.3 degrees that’s used to measure objects rotating in circular motion.
If we divide a circle’s value of 360 degrees by the 57.3 degrees that represent a *radian,* we find there are 6.28 radians in a circle, and oddly enough, it just so happens that 6.28 is equal to 2 × *π*. Anyone who stayed awake during math class can’t help but remember that *π* represents a constant value of 3.14, a number that pops up anytime you divide the circumference of a circle by its diameter. No matter the circle’s size, *π *will always result when you perform this operation.
Applying these facts to *radians,* we find that during one complete revolution of a **flywheel** the measure of the *angle* *θ* increases from 0 radians to 2*π* radians.
Suppose we have a flywheel spinning at *N* revolutions per minute, or RPMs. To calculate the *angular velocity,* ω, of any point on the flywheel, or the whole wheel for that matter, we use the following formula which provides an answer in radians per second,
*ω = *[2 × *π × **N* ] ÷ 60 *seconds/minute* (1)
If a **flywheel** spins at 3000 RPM, its *angular velocity* is calculated as,
*ω = *[2 × *π ×* (3000 RPM)] ÷ 60* seconds/minute* (2)
*ω = *314.16 *radians/second* (3)
Next time we’ll see how *angular velocity* is used to determine the kinetic energy contained within a flywheel.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: angular velocity, degrees, engineering, flywheel, kinetic energy, radians, revolutions per minute, RPM

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Radians and the Angular Velocity of a Flywheel

Wednesday, October 4th, 2017
We introduced the **flywheel** in our last blog and the fact that as long as it’s spinning it acts as a *kinetic energy *storage device. Today we’ll work our way towards an understanding of how this happens when we discuss *angular velocity*.
*Angular velocity* is represented in engineering and physics by the symbol, ω, the Greek letter Omega. The term *angular* is used to denote physical quantities measured with respect to an angle, especially those quantities associated with rotation.
__Angular Velocity of a Flywheel__
To understand how *angular velocity* manifests let’s consider a fixed point on the face of a **flywheel**, represented in the illustration as *A. *When the flywheel is at rest, point *A* is in the 12 o’clock position, and as it spins *A* travels clockwise in a circular path. An angle, *θ*, is formed as *A*’s position follows along with the rotation of the flywheel. The angle increases in size as *A* travels further from its starting point. If *A *moves one complete revolution, *θ* will equal 360 degrees, or the total number of degrees present in a circle.
As the **flywheel** spins through its first revolution into its second, point *A* travels past its point of origination, and in two complete revolutions it will travel 2 × 360, or 720 degrees, in three revolutions 3 × 360, or 1080 degrees, and so forth. The degrees *A* travels continue to increase with each revolution of the flywheel.
*Angular velocity* represents the total number of degrees *A* travels within a given time period. If we measure the flywheel’s rotational speed with a tachometer and find it takes one second to make 50 revolutions, point *A* will have traveled the circumference of its path fifty times, and *A*’s *angular velocity* would be calculated as,
*ω = *(50* revolutions per second*) × (360 *degrees per revolution*)
*ω = *18,000 *d*e*grees per second*
Next time we’ll introduce a unit of measurement known as radians which is uniquely used to measuring the angles of circular motion.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: angular velocity, energy storage, engineering, flywheel, kinetic energy

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Angular Velocity of a Flywheel

Monday, September 25th, 2017
*What came first? The wheel or the flywheel?* Archeologists have been debating this question for decades. One thing is certain, they both date back to prehistoric times.
__What Came First? The Wheel or the Flywheel?__
One of the oldest *flywheel* discoveries was a potter’s *wheel,* used to make pottery. It’s a turntable made of stone or heavy wood that’s connected to a massive wheel by a spinning shaft. Once the potter got the flywheel spinning with his hand or foot, the wheel’s heavy weight kept it in virtual perpetual motion, allowing the potter to concentrate on forming the clay he shaped with his hands.
A potter’s *wheel,* or any other *flywheel* for that matter, takes a lot of initial effort to put into motion. In other words, the potter must put a lot of his own muscles’ mechanical energy into the flywheel to get it moving. That’s because its sheer weight binds it to the *Law of* *Inertia *and makes it want to stay at rest.
But once the *flywheel* is in motion, the potter’s mechanical energy input is transformed into kinetic energy, the energy of motion. The kinetic energy the potter produces by his efforts results in surplus energy stored within the flywheel. Hence, the flywheel serves as a kinetic energy storage device, similar to a battery which stores electrical energy. As long as the flywheel remains in motion, this stored energy will be used to keep the turntable spinning, which results in no additional mechanical energy needing to be exerted by the potter while forming pots.
The *flywheel’s* stored energy also makes it hard to stop once it’s in motion. But eventually the frictional force between the potter’s hands and the clay he works drains off all stored kinetic energy.
Since the Industrial Revolution flywheels have been used to store kinetic energy to satisfy energy demands and provide a continuous output of power, which increases mechanical efficiency.
Next time we’ll begin our exploration into the science behind flywheels and see how they’re used in diverse engineering applications.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: energy storage, engineering, flywheel, frictional force, inertia, kinetic energy, mechanical energy

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on What Came First? The Wheel or the Flywheel?

Friday, September 15th, 2017
It’s been awhile since we began our discussion of a pulley-belt assembly operating within a hydroponics plant, and we’ve solved for a lot variables and derived many equations along the way. Today we’ll tackle the two remaining variables, *T*_{1 }, the belt’s tight side tension, and *T*_{2} , its loose side tension, and we’ll determine exactly what *belt width* will *optimize* power transmission within our system.
__Optimizing Belt Width in a Pulley-Belt Assembly__
Last time we converted mechanical power, *P*, from horsepower into foot-pounds per second and the belt’s velocity, *V*, into feet per second in order to get things into terms we can work with. We then inserted these values into the mechanical power formula to get,
2,200 *foot pounds per second = (T*_{1} – T_{2}) × 3.93 *feet/second* (1)
This equation will allow us to solve for *T*_{1} and *T*_{2}, and from there we’ll develop a value for the *optimum belt width.*
Previously, we determined from the Euler-Eytelwein Formula that,
*T*_{1} = 2.38*T*_{2} (2)
Substituting equation (2) into equation (1), we get,
2,200 *foot pounds per second* = (2.38*T*_{2} – T_{2}) × 3.93 *feet/second* (3)
Reducing this equation with algebra we arrive at,
*T*_{2} = 405.65 *pounds* (4)
We can now insert equation (4) into equation (2) and calculate *T*_{1},
*T*_{1} = 2.38 × 405.65 *pounds* (5)
*T*_{1} = 965.44* pounds* (6)
*T*_{1} is maximum tension in the *belt,* specified by the manufacturer to be 300 pounds per inch of *width*, which makes the minimum *width belt* to be used to *optimize* power transmission within our pulley-belt assembly,
*w =* *T*_{1} ÷* *300* pounds per inch * (7)
*w =* 965.44* pounds ÷** *300* pounds per inch* (8)
*w =* 3.22* inches* (9)
We can use a *belt* of minimum *width* of 3.22 inches to safely transmit 4 horsepower from the engine to the pump without incurring breakage and slippage along the belt, thereby *optimizing* power transmission within our assembly. If we used a narrower belt, breaking and slippage would occur. If we used a wider *belt,* an unnecessary expense would be incurred.
Next time we’ll begin a discussion on flywheels as they apply to rotating machinery like gasoline and steam engines.
Copyright 2017 – Philip J. O’Keefe, PE
Engineering Expert Witness Blog
____________________________________ |

Tags: belt, belt width, belt-pulley assembly, loose side tension, maximum tension, mechanical power, optimizing power transmission, pulley, slippage, tight side tension

Posted in Engineering and Science, Expert Witness, Forensic Engineering, Innovation and Intellectual Property, Personal Injury, Product Liability | Comments Off on Optimizing Belt Width in a Pulley-Belt Assembly